Hello footswitch,
Glad to read you again in this post.
As for my Z, I finally bought a used OBC that I repaired, same symptoms as electronpusher : I just changed a blue capacitor in the doghouse.
But I hope now to repair the old one: I just desoldered the waffle plate to test the IBGT one by...
I reread pages 5 to 10 of this thread concerning the installation of this charger on a test bench with you skylogger and coulomb.
I also reread the message of skylogger which advises me page 33 to solder wires onto the pins on the connectors along the white strips of the bottom PCB
I want to do...
Hello Kiev,
Ok, you are wright, I won't mix the charger parts #1 and #2
Can you update page 1 of this thread with my charger exchanged by a repaired charger?
Indeed, it is not the same type of failure. In one case (mine) the failure is downstream of the filter, in other cases the failures are...
Hello tout le monde
Finally, I bought a second charger (thanks to the french forum). The owner changed his charger by a new Citroen, and he had the good idea to recover the charger out of order
I only changed one of the two 1000 pF capacitors
The two resistors 4R7 were good and the relay too...
I get this message when the car is "READY"
Icarsoft can read 20/24 sections off the OBD.
4 sections cannot be read, like "On board charger" and three other.
Hello Kiev,
I changed all this components :
Both 4.7ohm resistor were fused
2.2µF capacitor was inflated
One of three 680µF capacitors was inflated, (I changed three)
To prevent other failures, I changed both 1000pF capacitors, and the relay
I just tested the 12VDC on the 12th pin
With the...
Hello tout le monde,
So I repaired my charrger
All details are on the following thread:
http://vehiculeselectriques.fr/viewtopic.php?f=60&t=16287
Unfortunatly , It does not work : I can not get into the ODB to clear it and reset,
With an Icarsoft i970: no communication on the On board...
Hello Kiev,
When the car is « READY », the 12V Aux battery voltage goes up to 14,5 V
Based on that, the 20A fuse is good, no ?
Do you think icarsoft i909 will works for my 2011 Czero?
Hello tout le monde,
I have just finished repairing my onboard charrger
A friend changed the three big capacitors 680 μF, the relay, the capacitor 2.2 μF, the two capacitors 1000 pF and both 4.7ohm resistors.
When I plug in my onboard charrger, the car does not start charging.
Do I have to...
Hello tout le monde,
I just acquired a charrger out of service. And so I ask myself the following question :
Can we mix the parts ?
exemple :
Repairing the bottom pcb from a charrger to connect it on the other?
Are top and bottom pcb paired?
Hello tout le monde
I have a question about the resistor P10K
Here is the technical sheet: https://imgur.com/6vaxWtx
first page is 10 watts:
second page is 5 watts
Is the power 5 Watt or 10 Watt?
I found a resistor 7 watt, and its height is 39 mm, so I just have raise the first pcb 5 mm...
Thank you for your answers to all.
To repair my PCB, I'll ask a friend to do the work, he has an electronics lab at the university.
I just have to buy all the components, and to remove the rubbery potting.
Are there small components hidden under the rubbery potting?
The P10K resistor is...
Hello tout le monde,
Today I made new photos. On this one we can see the fused resistor. I did not see last time. We also see that the rubbery potting has boiled.
Another problem, the 2x 2.2 microfarad capacitor seems inflated on both long sides.
Good news: the relay operates with a 4.5 volt...